Entries by linda

EZCAD Software show Can Not Find the LMC1 Drive?

February 11, 2020 /0 Comments/in /by

EZCAD Software show Can Not Find the LMC1 Drive?

When open ezcad software,it show can’t find the LMC1 Driver.

Here are the solution to check this problem.

1) USB line problem, After the device is powered off, re-plug the cable and restart it; Or just change the USB line.

2)  Software is broken. Delete all EzCad software in computer, copy new one and install the drive.

3) Control board is broken: After opening the hardware device manager, the hardware driver of the board cannot be found, there is no hardware prompt after re-plugging, or the prompt does not recognize the hardware. In this case, consider replacing the new board.
Whatsapp

86 13854105019
Wechat

86 13854105019
Skype

ChinaLindahao
Email

sales@sismarlaser.com

#EZCAD #LaserMarkingMachine #FiberLaserMarkingMachine #UVLaserMarkingMachine #GreenLaserMarkingMachine #Co2LaserMarkingMachine #LaserMarking #LaserMarker #Laser #LaserEngraver #LaserCuttingMachine #LaserCutter

Fiber Laser Marking Machine’s Red dot is running, but no marking?

February 9, 2020 /0 Comments/in /by

Red dot is running, but no marking?

5/5

Operation problem:

First, check if the material can absorb the 1064nm laser wavelength.
Second, if on the correct focus distance marking? What’s the output laser power? If it is bigger lens? Usually the laser will be weaker for bigger lens, also the depth of focus is relatively shallow, prone to this situation.
Third, check the marking content, if it is JPG or BMP format picture.
How to check on this situation? Use a piece of stainless steel, type TEXT, HATCH line distance is 0.05, laser power is 80%, speed is 500, chose Continue, then marking, up and down the marking head, will find where the problem from.

5/5

Parameter setting problem

Check the laser control model, if chose YAG model.

The laser control of fiber

The laser control of fiber

5/5

Laser source problem

If all the above 2 checked well, then will be laser source problem.

Fist, cut off the whole machine for 5 minutes, then reboot, if still can not mark, then need to check the laser source. Put the white dimming paper below the marking head, if can see the green laser spot. If can not, then laser source problem, further troubleshooting is required to resolve the problem either by laser failure or laser power failure

LaserWork Software Operation

February 8, 2020 /0 Comments/in /by

Co2 Laser Engraving Cutting Software Operation

5/5

How to Install laserwork extension for CorelDraw

5/5

Non-Metal and Metal Laser Cutting Software Operation

5/5

How to set Reverse in RD Laserwork software

EZCAD Software Operation

February 6, 2020 /0 Comments/in /by

EZCAD Software Operation

Fiber Laser Marking machine software is called EZCAD,made by  BJJCZ.

It is the most popular in market,very easy to operate and more powerful function. 

Here are EZCAD basic function video and user manual download.

Download User Manual

SISMAR LASER
whatsapp:86 13854105019

5/10

Popular function of EZCAD software

How to laser engraving photo

Laser Engraving Cutting

Pen Laser Engraving

3 Quick solutions to check Red dot is running, but no marking?

September 20, 2019 /0 Comments/in /by

"Red dot is running, but no marking"-Fiber Laser Marking Machine

During using fiber laser marking machine,we may encounder following problem-Fiber laser marking machine Red dot is running,but no marking.

Here are we list three steps,help you find the solution.

1.Operation problem:

First, check if the material can absorb the 1064nm laser wavelength.

Second, pls kindly check fiber laser marking machine,if on the correct focus distance marking? What’s the output laser power? If it is bigger lens? Usually the laser will be weaker for bigger lens, also the depth of focus is relatively shallow, prone to this situation.

Third, check the marking content, if it is JPG or BMP format picture.

How to check on this situation?

Use a piece of stainless steel, type TEXT, HATCH line distance is 0.05, laser power is 80%, speed is 500, chose Continue, then marking, up and down marking head, then we will find where the problem from.

2.Parameter setting problem:

Check the laser control model.

It is in Fiber Laser model or not,if not,change into Fiber Laser model.

The laser control of fiber:

3.Laser source problem:

If above info are well, let us check fiber laser source or laser power supply.

Fist, cut off the whole machine for 5 minutes, then reboot.if still can not mark, then need to check the laser source.

uninstall F-theta lens,adjust parameter as follows:

Put the white dimming piece below the marking head,pls kindly check if you can see the green laser spot on dimming piece. If can not, then laser source problem, further trouble shooting is required to resolve the problem either by laser failure or laser power failure

If you need more solution step,contact us by whatsapp/wechat:0086 13854105019 sales@sismarlaser.com

#LaserMarkingMachine #FiberLaserMarkingMachine #LaserEngravingMachine #LaserCuttingMachine #Co2LaserEngravingMachine #LaserMarker #FiberLaserMarker #Co2LaserCutter #Co2LaserEngraver #FiberLaserSource #LaserSource

Laser Marking Electronic Components

September 16, 2019 /0 Comments/in /by

Laser Marking Electronics Components

Nowadays the electronics industry has adopted the process of laser marking of electrical components as a standard process for guaranteeing the maximum quality and durability of the information marked.

Advantage

Laser marking on electrical material is permanent, and ideal for engraving texts, logos, instructions and much more on any type of material in an extremely flexible, fast and qualitatively unparalleled way.

Application

1.Laser Marking Phone Cover

2.Laser Marking Phone Accessories

3.Laser Marking Mobile Phone Chip

4.Laser Marking Mobile Phone parts

5.Laser Marking Mobile Phone Decorations

Laser Marking Samples show

Laser Marking Phone

Laser Marking Phone Accessories

Laser Marking Phone Chips

Laser Marking Spare parts

Laser Marking Phone Decoration

Fiber Laser Cutting Machine for Jewelry

September 10, 2019 /0 Comments/in /by

Jewelry Laser Engraving Cutting

You know many hand jewelry designer and manufacturer encounter the problem of working efficiency low,they are continually looking for reliable solutions for producing precision cutting of precious metals.

Mini and Mini cover laser-Laser marking, engraving & laser cutting machines from SISMAR laser, is the most suited tool for Jewelers and Goldsmiths as it allows them versatility, quality, precision that their customers need and deserve.

Applications of Mini Cover/Mini Fiber laser in Jewelry marking and designing

1.Laser jewellery etching, marking, surface engraving of jewelry,

2.Deep engraving to make dies for jewelry making,

3.Photo etching and picture marking on jewelry

4.Cutting of gold or silver to make jewelry pieces like earrings, rings, lockets, pendants etc.

 

What is max thickness can cut or deep engrave by Mini cover/Mini Fiber laser

1)The gold silver and brass material cutting range from 0.1 to 1.5mm;

the cutting time depend on cutting patterns and cutting size;

different cutting size spend different time.

Most our customers cut 0.5mm0.7mm 0.8mm and 1mm gold silver brass material for jewelry.The cutting size range from30mm to 100mm.

2)Aluminum ,stainless steel ,carbon steel for deep engrave from 0.5mm to 1.5mm by 50W fiber laser machine.

Deep engrave 0.5mm on 2mm aluminum by Fiber Laser machine

Two video tell you how fiber laser cutting name necklace;Engraving ring inside and outside

More info need,pls kindly contact us by email sales@sismarlaser.com Whatsapp/wechat:0086 13854105019


Facebook



Youtube



Instagram



Linkedin